\relax 
\@writefile{toc}{\contentsline {section}{\numberline {1}Attiny Solar Energy Harvest Tests}{1}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.1}Micro Considerations}{1}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.1.1}Micro Notes}{1}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.1.2}Energy Storage}{1}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.1.3}Make parts, not scrap}{2}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.2}Programming}{2}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.1}Testing Arduino Loader}{2}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.2}Conclusion on Arduino Programming Attiny10}{5}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.3}IO Port Switching Speed}{5}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.4}VCC 1.8V}{6}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.3}Application}{6}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.1}Magnetic Current Sensor}{7}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.2}Accelerometers}{7}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.3}Temperature Sensors}{8}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.4}Gas Sensors}{8}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.5}Supercap}{8}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.6}Hall Effect Sensors - Push Pull vs Open Drain Outputs}{8}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.7}Conclusion: Starting Sensors}{9}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.8}Farad to mA}{9}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.4}PCB}{9}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.1}PCB Programming}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.2}PCB programming and use}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.3}PCB Rev3}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.4}RF Comms}{11}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.5}Present Questions}{11}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.6}Plan of attack}{12}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.7}Other Sensors}{12}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.8}RF Searching}{12}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.9}PCB Rev 5}{13}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.10}Input Protection on Accidental Reverse Cable Hookup}{14}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.11}Nuts \& Volts 433MHz RF Transmitters}{14}}
\@writefile{lof}{\contentsline {figure}{\numberline {1}{\ignorespaces simple rx tx on 433mhz\relax }}{14}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.5}Connecting to Programmer}{15}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.6}Attiny10 Timer Fail}{15}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.6.1}AVR-objdump -S}{16}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.7}Attiny10 w/Solar and w/433MHz TX}{17}}
\@writefile{lof}{\contentsline {figure}{\numberline {2}{\ignorespaces With a \_delay\_ms, there is no ramping up. But, the delay had to be a minimum, otherwise some ramping did occur. It's very slow, but usable for things without a lot of data to transmit.\relax }}{17}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.7.1}433MHz Module TX Max Speed}{18}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.8}Further Notes}{18}}