You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
85 lines
4.1 KiB
85 lines
4.1 KiB
|
|
\documentclass[11pt]{article}
|
|
%Gummi|065|=)
|
|
\usepackage{graphicx}
|
|
\usepackage{caption}
|
|
\title{\textbf{HP Pavilion 15 Repair}}
|
|
\author{Steak Electronics}
|
|
\date{}
|
|
\begin{document}
|
|
|
|
\maketitle
|
|
|
|
\section{Overview}
|
|
|
|
User spilled tonic water on a laptop, then kept it powered on and continued to use it (this was a mistake. Turning it off, and removing battery / power, letting the liquid dry, is always the first step in a spill). The next morning the laptop would not power on.
|
|
\section{Equipment}
|
|
Laptop is an HP Pavilion 15 CS model. They are fairly new (date codes on micros are from 2018), and retailing around 500-600 dollars as of just before 2019.
|
|
\includegraphics[scale=0.2]{../pics/DSCN1016.JPG}
|
|
\captionof{figure}{HP}
|
|
\section{Disassembly}
|
|
There is no video tutorial on this online, but the steps are: Remove visible screws from the back of the case. Remove rubber feet, and screws beneath them. Pry open case from edges with plastic spudger tool to remove the clips. You must be careful, as the clips and case are fragile.
|
|
\begin{itemize}
|
|
\item Where to start with the spudger, and also showing the screwholes underneath the rubber feet.
|
|
|
|
\includegraphics[scale=0.2]{../pics/DSCN1019.JPG}
|
|
\captionof{figure}{Disassembly}
|
|
\item I was able to scratch the case with the plastic spudger. Be careful!
|
|
|
|
\includegraphics[scale=0.2]{../pics/DSCN1021.JPG}
|
|
\captionof{figure}{Disassembly}
|
|
\item The case can also crack from pulling it. I didn't pull this hard, but the brittle weak case cracked slightly.
|
|
|
|
\includegraphics[scale=0.3]{../pics/DSCN1022.JPG}
|
|
\captionof{figure}{Disassembly}
|
|
\item Finally we are in.
|
|
|
|
\includegraphics[scale=0.3]{../pics/DSCN1023.JPG}
|
|
\captionof{figure}{Disassembly}
|
|
\includegraphics[scale=0.3]{../pics/DSCN1024.JPG}
|
|
\captionof{figure}{Disassembly}
|
|
\item Screws are labeled, to help illustrate what size each is:
|
|
|
|
\includegraphics[scale=0.2]{../pics/DSCN1026.JPG}
|
|
\captionof{figure}{Disassembly}
|
|
|
|
\end{itemize}
|
|
|
|
|
|
|
|
|
|
|
|
\section{Diagnosis and Repair Log}
|
|
Now we will try to find out what is wrong.
|
|
\begin{itemize}
|
|
\item Right away I can see some visible marring from a likely shorted component. This is where a lot of the soda residue is.
|
|
|
|
\includegraphics[scale=0.4]{../pics/DSCN1029.JPG}
|
|
\captionof{figure}{Repair}
|
|
|
|
\item You can see a layer of cellophane that is in place to protect against spills. Amazing how millions of man hours can go into designing computers, yet a single glass of liquid can destroy one. Something is wrong, here. Crazy.
|
|
|
|
\includegraphics[scale=0.2]{../pics/DSCN1034.JPG}
|
|
\captionof{figure}{Repair}
|
|
|
|
\item This switcher, the BACAAB (?) chip is the one that has the failed components. I need a replacement but can't find a data sheet on it. I tried probing at some of the pins to see what was going on, and if I could understand a bit more about this, but due to me probing too close to the pins, (and a few factors, primarily the small package, but no leads, and also the fact I should've used the pads NEAR but not ON the package, I shorted something, and a spark resulted. While I saw a 2.4V signal on a pin, after the short, I was unable to find anything. The battery being removed and replaced did not bring it back.
|
|
|
|
\includegraphics[scale=0.3]{../pics/DSCN1036.JPG}
|
|
\captionof{figure}{Repair}
|
|
|
|
\item At this point, this chip, which I am unsure of what it is, appears to have a short and is overheating / shorting. I will need to get a motherboard donor at this point, to further repair the mistakes. As these are new boards, motherboards are not yet cheap enough to make this viable, so I will wait and try again at a later date.
|
|
|
|
\includegraphics[scale=0.3]{../pics/DSCN1037.JPG}
|
|
\captionof{figure}{Repair}
|
|
|
|
\item During my troubleshooting, I did find an open resistor, and a capacitor that has visible charring on its solder joint. I'll need to replace these as well. I should've replaced this at first, but without a schematic, I don't know what value the cap should be. The resistor is labeled as 1R0, but reads open. There may also be one other cap that has failed. However, some other components appear OK.
|
|
|
|
\includegraphics[scale=0.3]{../pics/DSCN1039.JPG}
|
|
\captionof{figure}{Site of failed components from soda water spill.}
|
|
|
|
\end{itemize}
|
|
|
|
|
|
|
|
|
|
\end{document}
|