|
|
- \contentsline {section}{\numberline {1}Attiny Solar Energy Harvest Tests}{2}
- \contentsline {subsection}{\numberline {1.1}Micro Considerations}{2}
- \contentsline {subsubsection}{\numberline {1.1.1}Micro Notes}{2}
- \contentsline {subsubsection}{\numberline {1.1.2}Energy Storage}{3}
- \contentsline {subsubsection}{\numberline {1.1.3}Make parts, not scrap}{3}
- \contentsline {subsection}{\numberline {1.2}Programming}{3}
- \contentsline {subsubsection}{\numberline {1.2.1}Testing Arduino Loader}{4}
- \contentsline {subsubsection}{\numberline {1.2.2}Conclusion on Arduino Programming Attiny10}{6}
- \contentsline {subsubsection}{\numberline {1.2.3}IO Port Switching Speed}{6}
- \contentsline {subsubsection}{\numberline {1.2.4}VCC 1.8V}{7}
- \contentsline {subsection}{\numberline {1.3}Application}{7}
- \contentsline {subsubsection}{\numberline {1.3.1}Magnetic Current Sensor}{8}
- \contentsline {subsubsection}{\numberline {1.3.2}Accelerometers}{8}
- \contentsline {subsubsection}{\numberline {1.3.3}Temperature Sensors}{9}
- \contentsline {subsubsection}{\numberline {1.3.4}Gas Sensors}{9}
- \contentsline {subsubsection}{\numberline {1.3.5}Supercap}{9}
- \contentsline {subsubsection}{\numberline {1.3.6}Hall Effect Sensors - Push Pull vs Open Drain Outputs}{9}
- \contentsline {subsubsection}{\numberline {1.3.7}Conclusion: Starting Sensors}{10}
- \contentsline {subsubsection}{\numberline {1.3.8}Farad to mA}{10}
- \contentsline {subsection}{\numberline {1.4}PCB}{10}
- \contentsline {subsubsection}{\numberline {1.4.1}PCB Programming}{11}
- \contentsline {subsubsection}{\numberline {1.4.2}PCB programming and use}{11}
- \contentsline {subsubsection}{\numberline {1.4.3}PCB Rev3}{11}
- \contentsline {subsubsection}{\numberline {1.4.4}RF Comms}{12}
- \contentsline {subsubsection}{\numberline {1.4.5}Present Questions}{12}
- \contentsline {subsubsection}{\numberline {1.4.6}Plan of attack}{13}
- \contentsline {subsubsection}{\numberline {1.4.7}Other Sensors}{13}
- \contentsline {subsubsection}{\numberline {1.4.8}RF Searching}{13}
- \contentsline {subsubsection}{\numberline {1.4.9}PCB Rev 5}{14}
- \contentsline {subsubsection}{\numberline {1.4.10}Input Protection on Accidental Reverse Cable Hookup}{15}
- \contentsline {subsubsection}{\numberline {1.4.11}Nuts \& Volts 433MHz RF Transmitters}{15}
- \contentsline {subsection}{\numberline {1.5}Connecting to Programmer}{16}
- \contentsline {subsection}{\numberline {1.6}Attiny10 Timer Fail}{16}
- \contentsline {subsubsection}{\numberline {1.6.1}AVR-objdump -S}{17}
- \contentsline {subsection}{\numberline {1.7}Attiny10 w/Solar and w/433MHz TX}{18}
- \contentsline {subsubsection}{\numberline {1.7.1}433MHz Module TX Max Speed}{19}
- \contentsline {subsection}{\numberline {1.8}Further Notes}{19}
|
