Electronics_Projects_2020/Attiny_Solar_Energy_Harvest/docs/50.aux

\relax 
\@writefile{toc}{\contentsline {section}{\numberline {1}Attiny Solar Energy Harvest Tests}{2}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.1}Micro Considerations}{2}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.1.1}Micro Notes}{2}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.1.2}Energy Storage}{3}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.1.3}Make parts, not scrap}{3}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.2}Programming}{3}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.1}Testing Arduino Loader}{4}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.2}Conclusion on Arduino Programming Attiny10}{6}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.3}IO Port Switching Speed}{6}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.2.4}VCC 1.8V}{7}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.3}Application}{7}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.1}Magnetic Current Sensor}{8}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.2}Accelerometers}{9}}
\@writefile{lof}{\contentsline {figure}{\numberline {1}{\ignorespaces Some pinouts are easier than others. That said, this would still benefit from a custom breakout board. Bridge the V+ and GND, omit NC, RES pins and then you will want hot air and solder paste. Those looking for trouble can try magnet wire in a pinch.\relax }}{9}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.3}Temperature Sensors}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.4}Gas Sensors}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.5}Supercap}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.6}Hall Effect Sensors - Push Pull vs Open Drain Outputs}{10}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.7}Conclusion: Starting Sensors}{11}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.3.8}Farad to mA}{11}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.4}PCB}{11}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.1}PCB Programming}{12}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.2}PCB programming and use}{12}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.3}PCB Rev3}{12}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.4}RF Comms}{13}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.5}Present Questions}{14}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.6}Plan of attack}{14}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.7}Other Sensors}{14}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.8}RF Searching}{15}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.9}PCB Rev 5}{16}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.10}Input Protection on Accidental Reverse Cable Hookup}{16}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.4.11}Nuts \& Volts 433MHz RF Transmitters}{16}}
\@writefile{lof}{\contentsline {figure}{\numberline {2}{\ignorespaces simple rx tx on 433mhz\relax }}{17}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.5}Connecting to Programmer Tips}{17}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.6}Attiny10 Timer Fail}{17}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.6.1}AVR-objdump -S}{18}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.7}Attiny10 w/Solar and w/433MHz TX}{19}}
\@writefile{lof}{\contentsline {figure}{\numberline {3}{\ignorespaces With a \_delay\_ms, there is no ramping up. But, the delay had to be a minimum, otherwise some ramping did occur. It's very slow, but usable for things without a lot of data to transmit.\relax }}{20}}
\@writefile{toc}{\contentsline {subsubsection}{\numberline {1.7.1}433MHz Module TX Max Speed}{21}}
\@writefile{toc}{\contentsline {subsection}{\numberline {1.8}Further Notes}{21}}