You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
85 lines
3.5 KiB
85 lines
3.5 KiB
|
|
\documentclass[11pt]{article}
|
|
%Gummi|065|=)
|
|
\usepackage{graphicx}
|
|
\usepackage{caption}
|
|
\usepackage{xcolor}
|
|
\usepackage[vcentering,dvips]{geometry}
|
|
\geometry{papersize={6in,9in},total={4.5in,6.8in}}
|
|
\title{\textbf{}}
|
|
\author{Steak Electronics}
|
|
\date{}
|
|
\begin{document}
|
|
|
|
%\maketitle
|
|
|
|
\tableofcontents
|
|
\textcolor{green!60!blue!70}{
|
|
\section{60Hz Divider}}
|
|
|
|
|
|
\subsection{Overview}
|
|
Let's count. There is a schematic in Practical Electronics For Beginners 4th edition. I've built that up, and will add some CPLD counter logic, along with a micro to output the SPI to a 7seg counter module.
|
|
|
|
The goal is relative accuracy. Not absolute. No GPS here. I'm going from 60 to 6,000 cycles.\footnote{Due to limitations of CPLD} This is just meant to be fun.
|
|
\subsection{Initial Notes: Counting the Hz}
|
|
pseudo code goal:
|
|
\begin{verbatim}
|
|
Using 1Hz signal
|
|
Start counting 1MHz every 1Hz
|
|
when next cycle is received,
|
|
display count
|
|
start counting again
|
|
\end{verbatim}
|
|
That's all the objective is here. Easy with a micro, but goal is to complete using cmos or 74 logic.
|
|
|
|
4553 x 5
|
|
74hct132
|
|
1MHz clock (or 6MHz clock), or some variation thereof
|
|
jk flip flop
|
|
74376 - quad jk flip flop
|
|
7476 - jk flip flop
|
|
1mhz clk will be main counter,
|
|
6 hz or 1 hz will be latch / reset
|
|
|
|
I ended up skipping the 74 CMOS, in favor of a CPLD. Practical Electronics also mentions this approach as favored. Even a micro alone could be used. Schematic entry in the CPLD could also be used.
|
|
|
|
\subsection{MAX7219 8 digit 7 LED segment Display Driver}
|
|
Basic code tested with this was the LedControl arduino library.
|
|
|
|
\begin{verbatim}
|
|
/*
|
|
Now we need a LedControl to work with.
|
|
***** These pin numbers will probably not work with your hardware *****
|
|
pin 12 is connected to the DataIn
|
|
pin 11 is connected to the CLK
|
|
pin 10 is connected to LOAD
|
|
We have only a single MAX72XX.
|
|
*/
|
|
\end{verbatim}
|
|
Some of the lines have to be edited to allow for all digits to be read, and
|
|
also to lower intensity of display. I think also a component package (dark
|
|
grey clear plastic bag) in front of the leds with intensity 1 is about right.
|
|
|
|
|
|
\subsection{CPLD Programming}
|
|
Using the XC9500XL series. This chip has some limitations - which are good.
|
|
|
|
As you get faster clocks, you need bigger registers to handle parsing the clocks. Bigger registers, use more power. Maybe this is one reason why high clock speeds mean more power.
|
|
|
|
\subsubsection{6KHz clock}
|
|
Due to limitations of the XC9500XL FPGA logic blocks, I ended up limiting the counter registers to 12+1 bits\footnote{Possibly I could use multiple smaller registers in a type of cascade, but let's not bother with that for now. I had 600KHz resolution, until I added the UART out/}, so I have around 6,000 (assuming 60Hz), resolution. With this, I need a 6KHz clock. I could do this with the uno, but let's throw an attiny in there because it's a good tool for this kind of purpose and resolution. It should be able to function as a rough 6KHz timer, easily.
|
|
|
|
|
|
\subsection{Divide by N Counters}
|
|
The schematics appear to be incorrect for the divide by 6 counter in the Practical Electronics for Beginners book. Having looked at my built up circuit carefully, I see a 20Hz output from the 60Hz. I managed to get my hands on a copy of the TTL Cookbook by Don Lancaster recently, and that details correct divide by 6 and 10 counters (which are different from what's on my proto board), and while I could fix the divide by 6 counter, instead, I'm going to build another divide by 2 counter, and leave the original incorrect one there as a warning (it's also easier to just build a new one).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
\end{document}
|
|
|