@ -0,0 +1,96 @@ | |||
#define HZin 4 | |||
uint32_t hzhigh[20]; | |||
uint32_t hzlow[20] ; | |||
uint8_t x = 0; | |||
void setup() { | |||
// put your setup code here, to run once: | |||
pinMode(HZin, INPUT); | |||
Serial.begin(116200); | |||
} | |||
void loop() { | |||
// put your main code here, to run repeatedly: | |||
//if (val = pulsein < 2000) then do low, then high again | |||
//else goto end | |||
/*if((hzhigh[x] = pulseInLong(HZin, HIGH, 1000000UL)) < 2000){ | |||
x++ | |||
hzlow[x] = pulseInLong( HZin, HIGH, 1000000UL); | |||
}*/ | |||
//if pulse high don't care | |||
//if pulse low, do stuff{ | |||
// whilepulse low, time, | |||
// while pulse high time, | |||
// etc... | |||
//if pulse high greater than 3ms, end | |||
//the below is not usable | |||
//apparently setup time is too long | |||
if((hzlow[x] = pulseInLong(HZin,LOW, 2000000UL))){ | |||
//while(hzhigh[x] < 2000){ | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
x++; | |||
hzhigh[x] = pulseInLong(HZin,HIGH,2000000UL); | |||
x++; | |||
hzlow[x] = pulseInLong(HZin,LOW, 2000000UL); | |||
} | |||
/* | |||
for(x=0;hzhigh[x]<2000;x++){ | |||
hzhigh[x] = pulseInLong( HZin, HIGH, 2000000UL); | |||
hzlow[x] = pulseInLong( HZin, LOW, 2000000UL); | |||
//hzhigh[x] = pulseInLong( HZin, HIGH, 2000000UL); | |||
} | |||
for(x=0;x<10;x++){ | |||
hzhigh[x] = hzhigh[x]>>5; | |||
hzlow[x] = hzlow[x]>>5; | |||
}*/ | |||
end: | |||
Serial.print("\n\n\n\n"); | |||
for(x=0;x<14;x++){ | |||
Serial.print("hi:"); | |||
Serial.print(x);Serial.print(" is:"); | |||
Serial.println(hzhigh[x]); | |||
Serial.print("low:"); | |||
Serial.print(x);Serial.print(" is:"); | |||
Serial.println(hzlow[x]); | |||
} | |||
for(x=0;x<14;x++){ | |||
hzhigh[x] = 0; | |||
hzlow[x] = 0; | |||
} | |||
delay(100); | |||
} |
@ -0,0 +1,113 @@ | |||
# | |||
# There exist several targets which are by default empty and which can be | |||
# used for execution of your targets. These targets are usually executed | |||
# before and after some main targets. They are: | |||
# | |||
# .build-pre: called before 'build' target | |||
# .build-post: called after 'build' target | |||
# .clean-pre: called before 'clean' target | |||
# .clean-post: called after 'clean' target | |||
# .clobber-pre: called before 'clobber' target | |||
# .clobber-post: called after 'clobber' target | |||
# .all-pre: called before 'all' target | |||
# .all-post: called after 'all' target | |||
# .help-pre: called before 'help' target | |||
# .help-post: called after 'help' target | |||
# | |||
# Targets beginning with '.' are not intended to be called on their own. | |||
# | |||
# Main targets can be executed directly, and they are: | |||
# | |||
# build build a specific configuration | |||
# clean remove built files from a configuration | |||
# clobber remove all built files | |||
# all build all configurations | |||
# help print help mesage | |||
# | |||
# Targets .build-impl, .clean-impl, .clobber-impl, .all-impl, and | |||
# .help-impl are implemented in nbproject/makefile-impl.mk. | |||
# | |||
# Available make variables: | |||
# | |||
# CND_BASEDIR base directory for relative paths | |||
# CND_DISTDIR default top distribution directory (build artifacts) | |||
# CND_BUILDDIR default top build directory (object files, ...) | |||
# CONF name of current configuration | |||
# CND_ARTIFACT_DIR_${CONF} directory of build artifact (current configuration) | |||
# CND_ARTIFACT_NAME_${CONF} name of build artifact (current configuration) | |||
# CND_ARTIFACT_PATH_${CONF} path to build artifact (current configuration) | |||
# CND_PACKAGE_DIR_${CONF} directory of package (current configuration) | |||
# CND_PACKAGE_NAME_${CONF} name of package (current configuration) | |||
# CND_PACKAGE_PATH_${CONF} path to package (current configuration) | |||
# | |||
# NOCDDL | |||
# Environment | |||
MKDIR=mkdir | |||
CP=cp | |||
CCADMIN=CCadmin | |||
RANLIB=ranlib | |||
# build | |||
build: .build-post | |||
.build-pre: | |||
# Add your pre 'build' code here... | |||
.build-post: .build-impl | |||
# Add your post 'build' code here... | |||
# clean | |||
clean: .clean-post | |||
.clean-pre: | |||
# Add your pre 'clean' code here... | |||
# WARNING: the IDE does not call this target since it takes a long time to | |||
# simply run make. Instead, the IDE removes the configuration directories | |||
# under build and dist directly without calling make. | |||
# This target is left here so people can do a clean when running a clean | |||
# outside the IDE. | |||
.clean-post: .clean-impl | |||
# Add your post 'clean' code here... | |||
# clobber | |||
clobber: .clobber-post | |||
.clobber-pre: | |||
# Add your pre 'clobber' code here... | |||
.clobber-post: .clobber-impl | |||
# Add your post 'clobber' code here... | |||
# all | |||
all: .all-post | |||
.all-pre: | |||
# Add your pre 'all' code here... | |||
.all-post: .all-impl | |||
# Add your post 'all' code here... | |||
# help | |||
help: .help-post | |||
.help-pre: | |||
# Add your pre 'help' code here... | |||
.help-post: .help-impl | |||
# Add your post 'help' code here... | |||
# include project implementation makefile | |||
include nbproject/Makefile-impl.mk | |||
# include project make variables | |||
include nbproject/Makefile-variables.mk |
@ -0,0 +1,43 @@ | |||
build/default/production/main.o.d build/default/production/main.o: main.c \ | |||
/opt/microchip/xc8/v2.10/avr/lib/gcc/avr/5.4.0/include/xc.h \ | |||
/opt/microchip/xc8/v2.10/avr/lib/gcc/avr/5.4.0/include/cci.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/io.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/sfr_defs.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/inttypes.h \ | |||
/opt/microchip/xc8/v2.10/avr/lib/gcc/avr/5.4.0/include/stdint.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/stdint.h \ | |||
/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/include/avr/iotn10.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/portpins.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/common.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/version.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/xmega.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/fuse.h \ | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/lock.h | |||
/opt/microchip/xc8/v2.10/avr/lib/gcc/avr/5.4.0/include/xc.h: | |||
/opt/microchip/xc8/v2.10/avr/lib/gcc/avr/5.4.0/include/cci.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/io.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/sfr_defs.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/inttypes.h: | |||
/opt/microchip/xc8/v2.10/avr/lib/gcc/avr/5.4.0/include/stdint.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/stdint.h: | |||
/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/include/avr/iotn10.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/portpins.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/common.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/version.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/xmega.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/fuse.h: | |||
/opt/microchip/xc8/v2.10/avr/avr/include/avr/lock.h: |
@ -0,0 +1,17 @@ | |||
<?xml version="1.0" encoding="UTF-8"?> | |||
<project> | |||
<executable name="dist/default/production/tests9_timer_6000hz.X.production.elf"> | |||
<memory name="program"> | |||
<units>bytes</units> | |||
<length>1024</length> | |||
<used>64</used> | |||
<free>960</free> | |||
</memory> | |||
<memory name="data"> | |||
<units>bytes</units> | |||
<length>32</length> | |||
<used>0</used> | |||
<free>32</free> | |||
</memory> | |||
</executable> | |||
</project> |
@ -0,0 +1,7 @@ | |||
:100000000AC01DC01CC01BC01AC019C018C017C030 | |||
:1000100016C015C014C011271FBFCFE5D0E0DEBF4A | |||
:0A002000CDBF03D000C0F894FFCF5D | |||
:10002A0048ED4CBF52E057BF4CBF48E046BF44E0E2 | |||
:04003A0040B9FECFFC | |||
:02003E00E0CF11 | |||
:00000001FF |
@ -0,0 +1,395 @@ | |||
Archive member included to satisfy reference by file (symbol) | |||
/opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o (exit) | |||
Discarded input sections | |||
.data 0x00000000 0x0 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.bss 0x00000000 0x0 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.text 0x00000000 0x0 build/default/production/main.o | |||
.data 0x00000000 0x0 build/default/production/main.o | |||
.bss 0x00000000 0x0 build/default/production/main.o | |||
.text 0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.data 0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.bss 0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc.mul | |||
0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc.div | |||
0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc.prologue | |||
0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc 0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc.builtins | |||
0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc.fmul | |||
0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
.text.libgcc.fixed | |||
0x00000000 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
Memory Configuration | |||
Name Origin Length Attributes | |||
text 0x00000000 0x00000400 xr | |||
data 0x00800040 0x00000020 rw !x | |||
config 0x00820000 0x00000001 rw !x | |||
lock 0x00830000 0x00000002 rw !x | |||
signature 0x00840000 0x00000004 rw !x | |||
*default* 0x00000000 0xffffffff | |||
Linker script and memory map | |||
0x00004000 __RODATA_PM_OFFSET__ = 0x4000 | |||
LOAD /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
0x00000001 __MPLAB_BUILD = 0x1 | |||
LOAD build/default/production/main.o | |||
START GROUP | |||
LOAD /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/../../../../avr/lib/avrtiny/libm.a | |||
END GROUP | |||
START GROUP | |||
LOAD /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a | |||
LOAD /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/../../../../avr/lib/avrtiny/libm.a | |||
LOAD /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/../../../../avr/lib/avrtiny/libc.a | |||
LOAD /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/libattiny10.a | |||
END GROUP | |||
0x00000000 __TEXT_REGION_ORIGIN__ = DEFINED (__TEXT_REGION_ORIGIN__)?__TEXT_REGION_ORIGIN__:0x0 | |||
[0x00800040] __DATA_REGION_ORIGIN__ = DEFINED (__DATA_REGION_ORIGIN__)?__DATA_REGION_ORIGIN__:0x800040 | |||
[0x00000400] __TEXT_REGION_LENGTH__ = DEFINED (__TEXT_REGION_LENGTH__)?__TEXT_REGION_LENGTH__:0x1000 | |||
[0x00000020] __DATA_REGION_LENGTH__ = DEFINED (__DATA_REGION_LENGTH__)?__DATA_REGION_LENGTH__:0x100 | |||
[0x00000001] __FUSE_REGION_LENGTH__ = DEFINED (__FUSE_REGION_LENGTH__)?__FUSE_REGION_LENGTH__:0x2 | |||
0x00000002 __LOCK_REGION_LENGTH__ = DEFINED (__LOCK_REGION_LENGTH__)?__LOCK_REGION_LENGTH__:0x2 | |||
0x00000004 __SIGNATURE_REGION_LENGTH__ = DEFINED (__SIGNATURE_REGION_LENGTH__)?__SIGNATURE_REGION_LENGTH__:0x4 | |||
0x00004000 __RODATA_PM_OFFSET__ = DEFINED (__RODATA_PM_OFFSET__)?__RODATA_PM_OFFSET__:0x4000 | |||
.hash | |||
*(.hash) | |||
.dynsym | |||
*(.dynsym) | |||
.dynstr | |||
*(.dynstr) | |||
.gnu.version | |||
*(.gnu.version) | |||
.gnu.version_d | |||
*(.gnu.version_d) | |||
.gnu.version_r | |||
*(.gnu.version_r) | |||
.rel.init | |||
*(.rel.init) | |||
.rela.init | |||
*(.rela.init) | |||
.rel.text | |||
*(.rel.text) | |||
*(.rel.text.*) | |||
*(.rel.gnu.linkonce.t*) | |||
.rela.text | |||
*(.rela.text) | |||
*(.rela.text.*) | |||
*(.rela.gnu.linkonce.t*) | |||
.rel.fini | |||
*(.rel.fini) | |||
.rela.fini | |||
*(.rela.fini) | |||
.rel.rodata | |||
*(.rel.rodata) | |||
*(.rel.rodata.*) | |||
*(.rel.gnu.linkonce.r*) | |||
.rela.rodata | |||
*(.rela.rodata) | |||
*(.rela.rodata.*) | |||
*(.rela.gnu.linkonce.r*) | |||
.rel.data | |||
*(.rel.data) | |||
*(.rel.data.*) | |||
*(.rel.gnu.linkonce.d*) | |||
.rela.data | |||
*(.rela.data) | |||
*(.rela.data.*) | |||
*(.rela.gnu.linkonce.d*) | |||
.rel.ctors | |||
*(.rel.ctors) | |||
.rela.ctors | |||
*(.rela.ctors) | |||
.rel.dtors | |||
*(.rel.dtors) | |||
.rela.dtors | |||
*(.rela.dtors) | |||
.rel.got | |||
*(.rel.got) | |||
.rela.got | |||
*(.rela.got) | |||
.rel.bss | |||
*(.rel.bss) | |||
.rela.bss | |||
*(.rela.bss) | |||
.rel.plt | |||
*(.rel.plt) | |||
.rela.plt | |||
*(.rela.plt) | |||
.text 0x00000000 0x2a | |||
*(.vectors) | |||
.vectors 0x00000000 0x16 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
0x00000000 __vectors | |||
0x00000000 __vector_default | |||
*(.vectors) | |||
*(.progmem.gcc*) | |||
*(.dinit) | |||
.dinit 0x00000016 0x0 data_init | |||
0x00000016 . = ALIGN (0x2) | |||
0x00000016 __trampolines_start = . | |||
*(.trampolines) | |||
.trampolines 0x00000016 0x0 linker stubs | |||
*(.trampolines*) | |||
0x00000016 __trampolines_end = . | |||
*libprintf_flt.a:*(.progmem.data) | |||
*libc.a:*(.progmem.data) | |||
0x00000016 . = ALIGN (0x2) | |||
*(.jumptables) | |||
*(.jumptables*) | |||
*(.lowtext) | |||
*(.lowtext*) | |||
0x00000016 __ctors_start = . | |||
*(.ctors) | |||
0x00000016 __ctors_end = . | |||
0x00000016 __dtors_start = . | |||
*(.dtors) | |||
0x00000016 __dtors_end = . | |||
SORT(*)(.ctors) | |||
SORT(*)(.dtors) | |||
*(.init0) | |||
.init0 0x00000016 0x0 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
0x00000016 __init | |||
*(.init0) | |||
*(.init1) | |||
*(.init1) | |||
*(.init2) | |||
.init2 0x00000016 0xc /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
*(.init2) | |||
*(.init3) | |||
*(.init3) | |||
*(.init4) | |||
*(.init4) | |||
*(.init5) | |||
*(.init5) | |||
*(.init6) | |||
*(.init6) | |||
*(.init7) | |||
*(.init7) | |||
*(.init8) | |||
*(.init8) | |||
*(.init9) | |||
.init9 0x00000022 0x4 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
*(.init9) | |||
0x00000026 . = ALIGN (0x2) | |||
*(.fini9) | |||
.fini9 0x00000026 0x0 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
0x00000026 exit | |||
0x00000026 _exit | |||
*(.fini9) | |||
*(.fini8) | |||
*(.fini8) | |||
*(.fini7) | |||
*(.fini7) | |||
*(.fini6) | |||
*(.fini6) | |||
*(.fini5) | |||
*(.fini5) | |||
*(.fini4) | |||
*(.fini4) | |||
*(.fini3) | |||
*(.fini3) | |||
*(.fini2) | |||
*(.fini2) | |||
*(.fini1) | |||
*(.fini1) | |||
*(.fini0) | |||
.fini0 0x00000026 0x4 /opt/microchip/xc8/v2.10/avr/bin/../lib/gcc/avr/5.4.0/avrtiny/libgcc.a(_exit.o) | |||
*(.fini0) | |||
0x0000002a _etext = . | |||
.rodata | |||
*(.rodata) | |||
*(.rodata*) | |||
*(.gnu.linkonce.r*) | |||
.data 0x00800040 0x0 load address 0x0000002a | |||
[!provide] PROVIDE (__data_start, .) | |||
*(.gnu.linkonce.d*) | |||
0x00800040 . = ALIGN (0x2) | |||
0x00800040 _edata = . | |||
[!provide] PROVIDE (__data_end, .) | |||
.bss 0x00800040 0x0 | |||
[!provide] PROVIDE (__bss_start, .) | |||
*(COMMON) | |||
[!provide] PROVIDE (__bss_end, .) | |||
0x0000002a __data_load_start = LOADADDR (.data) | |||
0x0000002a __data_load_end = (__data_load_start + SIZEOF (.data)) | |||
.noinit 0x00800040 0x0 | |||
[!provide] PROVIDE (__noinit_start, .) | |||
*(.noinit*) | |||
[!provide] PROVIDE (__noinit_end, .) | |||
0x00800040 _end = . | |||
.lock | |||
*(.lock*) | |||
.signature | |||
*(.signature*) | |||
.config | |||
*(.fuse) | |||
*(.lfuse) | |||
*(.hfuse) | |||
*(.efuse) | |||
*(.config*) | |||
.stab | |||
*(.stab) | |||
.stabstr | |||
*(.stabstr) | |||
.stab.excl | |||
*(.stab.excl) | |||
.stab.exclstr | |||
*(.stab.exclstr) | |||
.stab.index | |||
*(.stab.index) | |||
.stab.indexstr | |||
*(.stab.indexstr) | |||
.comment 0x00000000 0x2f | |||
*(.comment) | |||
.comment 0x00000000 0x2f build/default/production/main.o | |||
0x30 (size before relaxing) | |||
.note.gnu.build-id | |||
*(.note.gnu.build-id) | |||
.debug | |||
*(.debug) | |||
.line | |||
*(.line) | |||
.debug_srcinfo | |||
*(.debug_srcinfo) | |||
.debug_sfnames | |||
*(.debug_sfnames) | |||
.debug_aranges 0x00000000 0x20 | |||
*(.debug_aranges) | |||
.debug_aranges | |||
0x00000000 0x20 build/default/production/main.o | |||
.debug_pubnames | |||
*(.debug_pubnames) | |||
.debug_info 0x00000000 0x53d | |||
*(.debug_info .gnu.linkonce.wi.*) | |||
.debug_info 0x00000000 0x305 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.debug_info 0x00000305 0x238 build/default/production/main.o | |||
.debug_abbrev 0x00000000 0x324 | |||
*(.debug_abbrev) | |||
.debug_abbrev 0x00000000 0x2d9 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.debug_abbrev 0x000002d9 0x4b build/default/production/main.o | |||
.debug_line 0x00000000 0x16d | |||
*(.debug_line .debug_line.* .debug_line_end) | |||
.debug_line 0x00000000 0xd9 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.debug_line 0x000000d9 0x94 build/default/production/main.o | |||
.debug_frame 0x00000000 0x24 | |||
*(.debug_frame) | |||
.debug_frame 0x00000000 0x24 build/default/production/main.o | |||
.debug_str 0x00000000 0x115 | |||
*(.debug_str) | |||
.debug_str 0x00000000 0x115 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.debug_str 0x00000115 0x0 build/default/production/main.o | |||
.debug_loc | |||
*(.debug_loc) | |||
.debug_macinfo | |||
*(.debug_macinfo) | |||
.debug_weaknames | |||
*(.debug_weaknames) | |||
.debug_funcnames | |||
*(.debug_funcnames) | |||
.debug_typenames | |||
*(.debug_typenames) | |||
.debug_varnames | |||
*(.debug_varnames) | |||
.debug_pubtypes | |||
*(.debug_pubtypes) | |||
.debug_ranges 0x00000000 0x10 | |||
*(.debug_ranges) | |||
.debug_ranges 0x00000000 0x10 build/default/production/main.o | |||
.debug_macro | |||
*(.debug_macro) | |||
OUTPUT(dist/default/production/tests9_timer_6000hz.X.production.elf elf32-avr) | |||
LOAD linker stubs | |||
LOAD data_init | |||
.note.gnu.avr.deviceinfo | |||
0x00000000 0x3c | |||
.note.gnu.avr.deviceinfo | |||
0x00000000 0x3c /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
.text.main 0x0000002a 0x14 | |||
.text.main 0x0000002a 0x14 build/default/production/main.o | |||
0x0000002a main | |||
.text 0x0000003e 0x2 | |||
.text 0x0000003e 0x2 /home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10/gcc/dev/attiny10/avrtiny/crtattiny10.o | |||
0x0000003e __vector_1 | |||
0x0000003e __bad_interrupt | |||
0x0000003e __vector_6 | |||
0x0000003e __vector_3 | |||
0x0000003e __vector_7 | |||
0x0000003e __vector_5 | |||
0x0000003e __vector_4 | |||
0x0000003e __vector_9 | |||
0x0000003e __vector_2 | |||
0x0000003e __vector_8 | |||
0x0000003e __vector_10 |
@ -0,0 +1,305 @@ | |||
#include <xc.h> | |||
#include <avr/io.h> | |||
//this req'd for (and before calling) delay | |||
//see delay.h | |||
//compiler optimizations must also be enabled | |||
//#define F_CPU 1536000 | |||
//#include <util/delay.h> | |||
//#include <avr/interrupt.h> | |||
//#include <avr/sleep.h> | |||
//#include <util/atomic.h> | |||
//#include <avr/wdt.h> | |||
//tests5 tested and works (at ~950hz). unplug cable to programmer to see pin 4 active. | |||
//however... | |||
//tests6 DEADEND | |||
//never worked right. giving up and using delay. | |||
//reference: https://www.avrfreaks.net/forum/sample-project-attiny10 | |||
//https://blog.podkalicki.com/attiny13-blinky-with-timer-compa/ | |||
//watchdog is too slow and inaccurate to get 6000Hz | |||
//ISR(TIM0_COMPA_vect) | |||
//{ | |||
// // Toggle PB2 Hi/Low depending on current state | |||
// PINB = 1<<2; | |||
// TIFR0 |= 1<<OCF0A; //clear flag (is this required here? documentation unclear) | |||
// //PORTB ^= _BV(LED_PIN); // toggle LED pin | |||
//} | |||
/* | |||
Delay in powerdown mode. Wake up by watchdog interrupt. | |||
* //NOTE: see earlier code, e.g. tests3 in attiny10 elec projects 2020 | |||
*/ | |||
/* | |||
void delay_power_down_wdt(uint8_t wdto) | |||
{ | |||
wdt_reset(); | |||
wdt_enable(wdto); | |||
WDTCSR |= (1<<WDIE); | |||
//so far (with 128Khz clk) this sleep will be about 30-40 seconds. | |||
//(however, I'll add the below to) | |||
//adjust sleep speed here: | |||
// 0110 is 1hz at 128KHz | |||
//WDTCSR |= (0<< WDP3); | |||
//WDTCSR |= (1<< WDP2); | |||
//WDTCSR |= (1<< WDP1); | |||
//WDTCSR |= (0<< WDP0); | |||
set_sleep_mode(SLEEP_MODE_PWR_DOWN); | |||
sleep_enable(); | |||
// Make sure interrups are enabled and the I flag is restored | |||
NONATOMIC_BLOCK(NONATOMIC_RESTORESTATE) | |||
{ | |||
sleep_cpu(); | |||
wdt_disable(); | |||
} | |||
sleep_disable(); | |||
} | |||
*/ | |||
int main(void) | |||
{ | |||
//// //Write CCP (to enable changing clock) | |||
CCP = 0xD8; | |||
//// //change CLK to 128KHz: | |||
// CLKMSR = 0b01; | |||
//change clk to 8mhz: | |||
//CLKMSR = 0b00; | |||
//use external clk: | |||
CLKMSR = 0b10; | |||
//again need CCP (to enable changing prescaler (this time)) | |||
CCP = 0xD8; | |||
//clock prescaler from divide by 8 (defualt) to none | |||
// prescaler of 1: | |||
//CLKPSR = 0b0000; | |||
// prescaler of 256: | |||
CLKPSR = 0b1000; | |||
//notes: test results (osccal is 8 bit) | |||
// osccal | hz output | |||
// 0xe6 10khz | |||
// 0x06 3.58khz | |||
// 0x0F 3.83Khz | |||
// 0x2F 4.62Khz | |||
// 0x5F 5.84Khz | |||
// 0x65 6.003KHz -winrar (for this chip)) | |||
// 0x8F 7.27Khz | |||
//OSCCAL = 0x65; | |||
//////// OCR0A = 0; | |||
//////// TCNT0 = 0; | |||
//////// TCCR0A = 0; | |||
//////// TCCR0B = 0; | |||
//////// | |||
//////// TCCR0A |= _BV(WGM01); // set timer counter mode to CTC | |||
//////// // TCCR0B |= _BV(CS02)|_BV(CS00); // set prescaler to 1024 (CLK=1200000Hz/1024/256=4.57Hz, 0.22s) | |||
//////// TCCR0B |= _BV(CS00); // set prescaler to 1 (CLK=1MHz/1) | |||
//OCR0A is 16 bits. in ASM it must be loaded separately. | |||
//in C, it can be loaded > 256? (test) | |||
//520 about 950hz, 25us wide pulse | |||
//OCR0A = 520; // with one timer, ever 166.667hz we want to count once (3000hz) | |||
//OCR0A = 1; //475hz | |||
//this goes to 475hz (pulses). doesn't make sense. | |||
//// OCR0AH = 0xFF; // | |||
//// OCR0AL = 0xFF; | |||
//attiny10 output compare broken apparently | |||
//this still 960hz, with 100us or so pulse size (high is 100us, low is longer) | |||
//OCR0A = 100; | |||
//inline asm to load values into 16 bit register | |||
//; variables | |||
//; For 1 Hz output, the timer delay has to be 1/2 second (1/2 second on / 1/2 second off) | |||
//; delay = OCR0A * 1024 * 8 / 8000000 | |||
//; for 1/2 second, OCR0A = 488 (0x01E8) | |||
//.EQU OCR0AHigh = 0x01 | |||
//.EQU OCR0ALow = 0xe8 | |||
// in bash type: printf "%x\n" 488 | |||
//.EQU OCR0AHigh = 0x02 | |||
//.EQU OCR0ALow = 0x08 | |||
// ldi r17, OCR0AHigh //; Sets the output compare register value | |||
//ldi r16, OCR0ALow | |||
//this asm doesn't work (why?) //perhaps OCR0A is really just 8 bits on attiny10...?) | |||
////// asm volatile( | |||
////// "ldi r17, 0x02" | |||
////// "ldi r16, 0x08" | |||
////// "out OCR0AH, r17" | |||
////// "out OCR0AL, r16" | |||
////// ); | |||
//this asm works | |||
// asm volatile("nop\n\t" | |||
//"nop\n\t" | |||
//"nop\n\t" | |||
//"nop\n\t" | |||
//::); | |||
//////// | |||
//////// TIMSK0 |= _BV(OCIE0A); // enable Timer CTC interrupt | |||
//////// | |||
// PB2 change to output | |||
// DDRB = 1<<2; | |||
//// sei(); | |||
//int x = 0; | |||
while(1) | |||
{ | |||
//this goes about 60.3KHz. | |||
//experiment FAIL | |||
//will just buy a 6KHz oscillator. | |||
PINB = 1<<2; | |||
//EDIT: disabled optimization in mplab (level 0) | |||
//and ended up geting much slower IO | |||
//asm("nop;"); | |||
//for(x=0;x<10;x++){ | |||
//note it's _delay_us not delay_us | |||
//delay_us(1) is 44.3KHz | |||
//_delay_us(8); //9 is 6.4KHz, 8 is roughly 7.2KHz | |||
//delay_us(10) is 5.8KHz | |||
//not much granularity there...) | |||
//so adding the following... | |||
//////////// if( x == 3){ | |||
//////////// _delay_us(4);//these two are 5.98 or so KHz | |||
//////////// x = 0; | |||
//////////// goto jump; | |||
//////////// } | |||
//////////// | |||
//////////// //NOTE: the above ends up causing an ugly looking clock. may not matter | |||
//////////// //for fpga clocking off of rising edge, BUT, it is ugly, should remove, | |||
//////////// //and just do single delay. Will do in part 9. | |||
//////////// | |||
//////////// x++; | |||
//////////// jump: | |||
//////////// //in combination with the jump, gives closer to 6KHz | |||
//////////// _delay_us(8); | |||
///below didn't work out, so using osccal | |||
//bit convuluted anyways | |||
/*if( x == 4){ | |||
_delay_us(1); | |||
//x = 0; | |||
goto jump; | |||
} | |||
if( x == 8){ | |||
_delay_us(2); | |||
x = 0; | |||
goto jump; | |||
} | |||
x++; | |||
jump: | |||
//in combination with the jump, gives closer to 6KHz | |||
_delay_us(8);*/ | |||
//the above idles at 5.98 - 5.99KHz. | |||
//best so far. | |||
//Now, calibrate oscillator with OSCCAL | |||
//if more accuracy desired. | |||
//or adjust if clause above | |||
//tried to make my own delay in ASM, BUT | |||
//compiler keeps optimizing it out (even w/out optimization enabled) | |||
//... some other flag may be culprit. So instead will use delay_us. Two delay | |||
//functions are delay_ms and delay_us. see headers at top and delay.h) | |||
/* __asm__("mov r16, r17;" | |||
"mov r17, r16;" | |||
"inc r16;" | |||
"dec r16;" | |||
"mov r16, r17;" | |||
"mov r17, r16;" | |||
"inc r16;" | |||
"dec r16;" | |||
"clr r16;" | |||
"clr r17;" | |||
"clr r18;" | |||
"clr r19;" | |||
"clr r20;" | |||
"clr r21;" | |||
"clr r22;" | |||
"clr r23;" | |||
"mov r16, r17;" | |||
"mov r17, r16;" | |||
"inc r16;" | |||
"dec r16;" | |||
"mov r16, r17;" | |||
"mov r17, r16;" | |||
"clr r16;" | |||
"clr r17;" | |||
"clr r18;" | |||
"clr r19;" | |||
"clr r20;" | |||
"clr r21;" | |||
"clr r22;" | |||
"clr r23;" | |||
"mov r16, r17;" | |||
"mov r17, r16;" | |||
"inc r16;" | |||
"dec r16;" | |||
"mov r16, r17;" | |||
"mov r17, r16;" | |||
);*/ | |||
//mplab delay is: | |||
/** \ingroup util_delay_basic | |||
Delay loop using an 8-bit counter \c __count, so up to 256 | |||
iterations are possible. (The value 256 would have to be passed | |||
as 0.) The loop executes three CPU cycles per iteration, not | |||
including the overhead the compiler needs to setup the counter | |||
register. | |||
Thus, at a CPU speed of 1 MHz, delays of up to 768 microseconds | |||
can be achieved. | |||
*/ | |||
//////////void | |||
//////////_delay_loop_1(uint8_t __count) | |||
//////////{ | |||
////////// __asm__ volatile ( | |||
////////// "1: dec %0" "\n\t" | |||
////////// "brne 1b" | |||
////////// : "=r" (__count) | |||
////////// : "0" (__count) | |||
////////// ); | |||
//////////} | |||
////////// | |||
////////// | |||
//ignore below | |||
// asm("nop;""nop;""nop;""nop;""nop;" | |||
//"nop;""nop;"//"nop;""nop;"//"nop;""nop;" | |||
//); | |||
//}//just this asm block is about 121.22KHz | |||
} | |||
} | |||
@ -0,0 +1,158 @@ | |||
# | |||
# Generated Makefile - do not edit! | |||
# | |||
# Edit the Makefile in the project folder instead (../Makefile). Each target | |||
# has a -pre and a -post target defined where you can add customized code. | |||
# | |||
# This makefile implements configuration specific macros and targets. | |||
# Include project Makefile | |||
ifeq "${IGNORE_LOCAL}" "TRUE" | |||
# do not include local makefile. User is passing all local related variables already | |||
else | |||
include Makefile | |||
# Include makefile containing local settings | |||
ifeq "$(wildcard nbproject/Makefile-local-default.mk)" "nbproject/Makefile-local-default.mk" | |||
include nbproject/Makefile-local-default.mk | |||
endif | |||
endif | |||
# Environment | |||
MKDIR=mkdir -p | |||
RM=rm -f | |||
MV=mv | |||
CP=cp | |||
# Macros | |||
CND_CONF=default | |||
ifeq ($(TYPE_IMAGE), DEBUG_RUN) | |||
IMAGE_TYPE=debug | |||
OUTPUT_SUFFIX=elf | |||
DEBUGGABLE_SUFFIX=elf | |||
FINAL_IMAGE=dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX} | |||
else | |||
IMAGE_TYPE=production | |||
OUTPUT_SUFFIX=hex | |||
DEBUGGABLE_SUFFIX=elf | |||
FINAL_IMAGE=dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX} | |||
endif | |||
ifeq ($(COMPARE_BUILD), true) | |||
COMPARISON_BUILD= | |||
else | |||
COMPARISON_BUILD= | |||
endif | |||
ifdef SUB_IMAGE_ADDRESS | |||
else | |||
SUB_IMAGE_ADDRESS_COMMAND= | |||
endif | |||
# Object Directory | |||
OBJECTDIR=build/${CND_CONF}/${IMAGE_TYPE} | |||
# Distribution Directory | |||
DISTDIR=dist/${CND_CONF}/${IMAGE_TYPE} | |||
# Source Files Quoted if spaced | |||
SOURCEFILES_QUOTED_IF_SPACED=main.c | |||
# Object Files Quoted if spaced | |||
OBJECTFILES_QUOTED_IF_SPACED=${OBJECTDIR}/main.o | |||
POSSIBLE_DEPFILES=${OBJECTDIR}/main.o.d | |||
# Object Files | |||
OBJECTFILES=${OBJECTDIR}/main.o | |||
# Source Files | |||
SOURCEFILES=main.c | |||
CFLAGS= | |||
ASFLAGS= | |||
LDLIBSOPTIONS= | |||
############# Tool locations ########################################## | |||
# If you copy a project from one host to another, the path where the # | |||
# compiler is installed may be different. # | |||
# If you open this project with MPLAB X in the new host, this # | |||
# makefile will be regenerated and the paths will be corrected. # | |||
####################################################################### | |||
# fixDeps replaces a bunch of sed/cat/printf statements that slow down the build | |||
FIXDEPS=fixDeps | |||
.build-conf: ${BUILD_SUBPROJECTS} | |||
ifneq ($(INFORMATION_MESSAGE), ) | |||
@echo $(INFORMATION_MESSAGE) | |||
endif | |||
${MAKE} -f nbproject/Makefile-default.mk dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX} | |||
MP_PROCESSOR_OPTION=ATtiny10 | |||
# ------------------------------------------------------------------------------------ | |||
# Rules for buildStep: compile | |||
ifeq ($(TYPE_IMAGE), DEBUG_RUN) | |||
${OBJECTDIR}/main.o: main.c nbproject/Makefile-${CND_CONF}.mk | |||
@${MKDIR} "${OBJECTDIR}" | |||
@${RM} ${OBJECTDIR}/main.o.d | |||
@${RM} ${OBJECTDIR}/main.o | |||
${MP_CC} $(MP_EXTRA_CC_PRE) -mcpu=$(MP_PROCESSOR_OPTION) -c -D__DEBUG=1 -g -DDEBUG -gdwarf-2 -x c -D__$(MP_PROCESSOR_OPTION)__ -mdfp="/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10" -Wl,--gc-sections -O1 -ffunction-sections -fdata-sections -fpack-struct -fshort-enums -funsigned-char -funsigned-bitfields -Wall -DXPRJ_default=$(CND_CONF) $(COMPARISON_BUILD) -gdwarf-3 -MD -MP -MF "${OBJECTDIR}/main.o.d" -MT "${OBJECTDIR}/main.o.d" -MT ${OBJECTDIR}/main.o -o ${OBJECTDIR}/main.o main.c | |||
else | |||
${OBJECTDIR}/main.o: main.c nbproject/Makefile-${CND_CONF}.mk | |||
@${MKDIR} "${OBJECTDIR}" | |||
@${RM} ${OBJECTDIR}/main.o.d | |||
@${RM} ${OBJECTDIR}/main.o | |||
${MP_CC} $(MP_EXTRA_CC_PRE) -mcpu=$(MP_PROCESSOR_OPTION) -c -x c -D__$(MP_PROCESSOR_OPTION)__ -mdfp="/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10" -Wl,--gc-sections -O1 -ffunction-sections -fdata-sections -fpack-struct -fshort-enums -funsigned-char -funsigned-bitfields -Wall -DXPRJ_default=$(CND_CONF) $(COMPARISON_BUILD) -gdwarf-3 -MD -MP -MF "${OBJECTDIR}/main.o.d" -MT "${OBJECTDIR}/main.o.d" -MT ${OBJECTDIR}/main.o -o ${OBJECTDIR}/main.o main.c | |||
endif | |||
# ------------------------------------------------------------------------------------ | |||
# Rules for buildStep: assemble | |||
ifeq ($(TYPE_IMAGE), DEBUG_RUN) | |||
else | |||
endif | |||
# ------------------------------------------------------------------------------------ | |||
# Rules for buildStep: assembleWithPreprocess | |||
ifeq ($(TYPE_IMAGE), DEBUG_RUN) | |||
else | |||
endif | |||
# ------------------------------------------------------------------------------------ | |||
# Rules for buildStep: link | |||
ifeq ($(TYPE_IMAGE), DEBUG_RUN) | |||
dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX}: ${OBJECTFILES} nbproject/Makefile-${CND_CONF}.mk | |||
@${MKDIR} dist/${CND_CONF}/${IMAGE_TYPE} | |||
${MP_CC} $(MP_EXTRA_LD_PRE) -mcpu=$(MP_PROCESSOR_OPTION) -Wl,-Map=dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.map -D__DEBUG=1 -DXPRJ_default=$(CND_CONF) -Wl,--defsym=__MPLAB_BUILD=1 -mdfp="/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10" -gdwarf-2 -Wl,--gc-sections -O1 -ffunction-sections -fdata-sections -fpack-struct -fshort-enums -funsigned-char -funsigned-bitfields -Wall -gdwarf-3 $(COMPARISON_BUILD) -Wl,--memorysummary,dist/${CND_CONF}/${IMAGE_TYPE}/memoryfile.xml -o dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} -o dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX} ${OBJECTFILES_QUOTED_IF_SPACED} -Wl,--start-group -Wl,-lm -Wl,--end-group -Wl,--defsym=__MPLAB_DEBUG=1,--defsym=__DEBUG=1 | |||
@${RM} dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.hex | |||
else | |||
dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX}: ${OBJECTFILES} nbproject/Makefile-${CND_CONF}.mk | |||
@${MKDIR} dist/${CND_CONF}/${IMAGE_TYPE} | |||
${MP_CC} $(MP_EXTRA_LD_PRE) -mcpu=$(MP_PROCESSOR_OPTION) -Wl,-Map=dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.map -DXPRJ_default=$(CND_CONF) -Wl,--defsym=__MPLAB_BUILD=1 -mdfp="/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10" -Wl,--gc-sections -O1 -ffunction-sections -fdata-sections -fpack-struct -fshort-enums -funsigned-char -funsigned-bitfields -Wall -gdwarf-3 $(COMPARISON_BUILD) -Wl,--memorysummary,dist/${CND_CONF}/${IMAGE_TYPE}/memoryfile.xml -o dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} -o dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} ${OBJECTFILES_QUOTED_IF_SPACED} -Wl,--start-group -Wl,-lm -Wl,--end-group | |||
${MP_CC_DIR}/avr-objcopy -O ihex "dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX}" "dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.hex" | |||
endif | |||
# Subprojects | |||
.build-subprojects: | |||
# Subprojects | |||
.clean-subprojects: | |||
# Clean Targets | |||
.clean-conf: ${CLEAN_SUBPROJECTS} | |||
${RM} -r build/default | |||
${RM} -r dist/default | |||
# Enable dependency checking | |||
.dep.inc: .depcheck-impl | |||
DEPFILES=$(shell "${PATH_TO_IDE_BIN}"mplabwildcard ${POSSIBLE_DEPFILES}) | |||
ifneq (${DEPFILES},) | |||
include ${DEPFILES} | |||
endif |
@ -0,0 +1,10 @@ | |||
# | |||
#Sat Aug 01 22:05:40 EDT 2020 | |||
default.Pack.dfplocation=/home/dev/.mchp_packs/Microchip/ATtiny_DFP/2.0.10 | |||
default.languagetoolchain.dir=/opt/microchip/xc8/v2.10/bin | |||
configurations-xml=5e854234238a55dafe0eba84ce6d1401 | |||
com-microchip-mplab-nbide-embedded-makeproject-MakeProject.md5=6e453b0cf7f7da72a932cfdb2f655401 | |||
default.languagetoolchain.version=2.10 | |||
host.platform=linux | |||
conf.ids=default | |||
default.com-microchip-mplab-nbide-toolchainXC8-XC8LanguageToolchain.md5=23d12c447ed4f9462f01e2202bc2f36a |
@ -0,0 +1,69 @@ | |||
# | |||
# Generated Makefile - do not edit! | |||
# | |||
# Edit the Makefile in the project folder instead (../Makefile). Each target | |||
# has a pre- and a post- target defined where you can add customization code. | |||
# | |||
# This makefile implements macros and targets common to all configurations. | |||
# | |||
# NOCDDL | |||
# Building and Cleaning subprojects are done by default, but can be controlled with the SUB | |||
# macro. If SUB=no, subprojects will not be built or cleaned. The following macro | |||
# statements set BUILD_SUB-CONF and CLEAN_SUB-CONF to .build-reqprojects-conf | |||
# and .clean-reqprojects-conf unless SUB has the value 'no' | |||
SUB_no=NO | |||
SUBPROJECTS=${SUB_${SUB}} | |||
BUILD_SUBPROJECTS_=.build-subprojects | |||
BUILD_SUBPROJECTS_NO= | |||
BUILD_SUBPROJECTS=${BUILD_SUBPROJECTS_${SUBPROJECTS}} | |||
CLEAN_SUBPROJECTS_=.clean-subprojects | |||
CLEAN_SUBPROJECTS_NO= | |||
CLEAN_SUBPROJECTS=${CLEAN_SUBPROJECTS_${SUBPROJECTS}} | |||
# Project Name | |||
PROJECTNAME=tests9_timer_6000hz.X | |||
# Active Configuration | |||
DEFAULTCONF=default | |||
CONF=${DEFAULTCONF} | |||
# All Configurations | |||
ALLCONFS=default | |||
# build | |||
.build-impl: .build-pre | |||
${MAKE} -f nbproject/Makefile-${CONF}.mk SUBPROJECTS=${SUBPROJECTS} .build-conf | |||
# clean | |||
.clean-impl: .clean-pre | |||
${MAKE} -f nbproject/Makefile-${CONF}.mk SUBPROJECTS=${SUBPROJECTS} .clean-conf | |||
# clobber | |||
.clobber-impl: .clobber-pre .depcheck-impl | |||
${MAKE} SUBPROJECTS=${SUBPROJECTS} CONF=default clean | |||
# all | |||
.all-impl: .all-pre .depcheck-impl | |||
${MAKE} SUBPROJECTS=${SUBPROJECTS} CONF=default build | |||
# dependency checking support | |||
.depcheck-impl: | |||
# @echo "# This code depends on make tool being used" >.dep.inc | |||
# @if [ -n "${MAKE_VERSION}" ]; then \ | |||
# echo "DEPFILES=\$$(wildcard \$$(addsuffix .d, \$${OBJECTFILES}))" >>.dep.inc; \ | |||
# echo "ifneq (\$${DEPFILES},)" >>.dep.inc; \ | |||
# echo "include \$${DEPFILES}" >>.dep.inc; \ | |||
# echo "endif" >>.dep.inc; \ | |||
# else \ | |||
# echo ".KEEP_STATE:" >>.dep.inc; \ | |||
# echo ".KEEP_STATE_FILE:.make.state.\$${CONF}" >>.dep.inc; \ | |||
# fi |
@ -0,0 +1,36 @@ | |||
# | |||
# Generated Makefile - do not edit! | |||
# | |||
# | |||
# This file contains information about the location of compilers and other tools. | |||
# If you commmit this file into your revision control server, you will be able to | |||
# to checkout the project and build it from the command line with make. However, | |||
# if more than one person works on the same project, then this file might show | |||
# conflicts since different users are bound to have compilers in different places. | |||
# In that case you might choose to not commit this file and let MPLAB X recreate this file | |||
# for each user. The disadvantage of not commiting this file is that you must run MPLAB X at | |||
# least once so the file gets created and the project can be built. Finally, you can also | |||
# avoid using this file at all if you are only building from the command line with make. | |||
# You can invoke make with the values of the macros: | |||
# $ makeMP_CC="/opt/microchip/mplabc30/v3.30c/bin/pic30-gcc" ... | |||
# | |||
PATH_TO_IDE_BIN=/opt/microchip/mplabx/v5.25/mplab_platform/platform/../mplab_ide/modules/../../bin/ | |||
# Adding MPLAB X bin directory to path. | |||
PATH:=/opt/microchip/mplabx/v5.25/mplab_platform/platform/../mplab_ide/modules/../../bin/:$(PATH) | |||
# Path to java used to run MPLAB X when this makefile was created | |||
MP_JAVA_PATH="/opt/microchip/mplabx/v5.25/sys/java/jre1.8.0_181/bin/" | |||
OS_CURRENT="$(shell uname -s)" | |||
MP_CC="/opt/microchip/xc8/v2.10/bin/xc8-cc" | |||
# MP_CPPC is not defined | |||
# MP_BC is not defined | |||
MP_AS="/opt/microchip/xc8/v2.10/bin/xc8-cc" | |||
MP_LD="/opt/microchip/xc8/v2.10/bin/xc8-cc" | |||
MP_AR="/opt/microchip/xc8/v2.10/bin/xc8-ar" | |||
DEP_GEN=${MP_JAVA_PATH}java -jar "/opt/microchip/mplabx/v5.25/mplab_platform/platform/../mplab_ide/modules/../../bin/extractobjectdependencies.jar" | |||
MP_CC_DIR="/opt/microchip/xc8/v2.10/bin" | |||
# MP_CPPC_DIR is not defined | |||
# MP_BC_DIR is not defined | |||
MP_AS_DIR="/opt/microchip/xc8/v2.10/bin" | |||
MP_LD_DIR="/opt/microchip/xc8/v2.10/bin" | |||
MP_AR_DIR="/opt/microchip/xc8/v2.10/bin" | |||
# MP_BC_DIR is not defined |
@ -0,0 +1,13 @@ | |||
# | |||
# Generated - do not edit! | |||
# | |||
# NOCDDL | |||
# | |||
CND_BASEDIR=`pwd` | |||
# default configuration | |||
CND_ARTIFACT_DIR_default=dist/default/production | |||
CND_ARTIFACT_NAME_default=tests9_timer_6000hz.X.production.hex | |||
CND_ARTIFACT_PATH_default=dist/default/production/tests9_timer_6000hz.X.production.hex | |||
CND_PACKAGE_DIR_default=${CND_DISTDIR}/default/package | |||
CND_PACKAGE_NAME_default=tests9timer6000hz.x.tar | |||
CND_PACKAGE_PATH_default=${CND_DISTDIR}/default/package/tests9timer6000hz.x.tar |
@ -0,0 +1,73 @@ | |||
#!/bin/bash -x | |||
# | |||
# Generated - do not edit! | |||
# | |||
# Macros | |||
TOP=`pwd` | |||
CND_CONF=default | |||
CND_DISTDIR=dist | |||
TMPDIR=build/${CND_CONF}/${IMAGE_TYPE}/tmp-packaging | |||
TMPDIRNAME=tmp-packaging | |||
OUTPUT_PATH=dist/${CND_CONF}/${IMAGE_TYPE}/tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX} | |||
OUTPUT_BASENAME=tests9_timer_6000hz.X.${IMAGE_TYPE}.${OUTPUT_SUFFIX} | |||
PACKAGE_TOP_DIR=tests9timer6000hz.x/ | |||
# Functions | |||
function checkReturnCode | |||
{ | |||
rc=$? | |||
if [ $rc != 0 ] | |||
then | |||
exit $rc | |||
fi | |||
} | |||
function makeDirectory | |||
# $1 directory path | |||
# $2 permission (optional) | |||
{ | |||
mkdir -p "$1" | |||
checkReturnCode | |||
if [ "$2" != "" ] | |||
then | |||
chmod $2 "$1" | |||
checkReturnCode | |||
fi | |||
} | |||
function copyFileToTmpDir | |||
# $1 from-file path | |||
# $2 to-file path | |||
# $3 permission | |||
{ | |||
cp "$1" "$2" | |||
checkReturnCode | |||
if [ "$3" != "" ] | |||
then | |||
chmod $3 "$2" | |||
checkReturnCode | |||
fi | |||
} | |||
# Setup | |||
cd "${TOP}" | |||
mkdir -p ${CND_DISTDIR}/${CND_CONF}/package | |||
rm -rf ${TMPDIR} | |||
mkdir -p ${TMPDIR} | |||
# Copy files and create directories and links | |||
cd "${TOP}" | |||
makeDirectory ${TMPDIR}/tests9timer6000hz.x/bin | |||
copyFileToTmpDir "${OUTPUT_PATH}" "${TMPDIR}/${PACKAGE_TOP_DIR}bin/${OUTPUT_BASENAME}" 0755 | |||
# Generate tar file | |||
cd "${TOP}" | |||
rm -f ${CND_DISTDIR}/${CND_CONF}/package/tests9timer6000hz.x.tar | |||
cd ${TMPDIR} | |||
tar -vcf ../../../../${CND_DISTDIR}/${CND_CONF}/package/tests9timer6000hz.x.tar * | |||
checkReturnCode | |||
# Cleanup | |||
cd "${TOP}" | |||
rm -rf ${TMPDIR} |
@ -0,0 +1,160 @@ | |||
<?xml version="1.0" encoding="UTF-8"?> | |||
<configurationDescriptor version="65"> | |||
<logicalFolder name="root" displayName="root" projectFiles="true"> | |||
<logicalFolder name="HeaderFiles" | |||
displayName="Header Files" | |||
projectFiles="true"> | |||
</logicalFolder> | |||
<logicalFolder name="LinkerScript" | |||
displayName="Linker Files" | |||
projectFiles="true"> | |||
</logicalFolder> | |||
<logicalFolder name="SourceFiles" | |||
displayName="Source Files" | |||
projectFiles="true"> | |||
<itemPath>main.c</itemPath> | |||
</logicalFolder> | |||
<logicalFolder name="ExternalFiles" | |||
displayName="Important Files" | |||
projectFiles="false"> | |||
<itemPath>Makefile</itemPath> | |||
</logicalFolder> | |||
</logicalFolder> | |||
<projectmakefile>Makefile</projectmakefile> | |||
<confs> | |||
<conf name="default" type="2"> | |||
<toolsSet> | |||
<developmentServer>localhost</developmentServer> | |||
<targetDevice>ATtiny10</targetDevice> | |||
<targetHeader></targetHeader> | |||
<targetPluginBoard></targetPluginBoard> | |||
<platformTool></platformTool> | |||
<languageToolchain>XC8</languageToolchain> | |||
<languageToolchainVersion>2.10</languageToolchainVersion> | |||
<platform>2</platform> | |||
</toolsSet> | |||
<packs> | |||
<pack name="ATtiny_DFP" vendor="Microchip" version="2.0.10"/> | |||
</packs> | |||
<compileType> | |||
<linkerTool> | |||
<linkerLibItems> | |||
</linkerLibItems> | |||
</linkerTool> | |||
<archiverTool> | |||
</archiverTool> | |||
<loading> | |||
<useAlternateLoadableFile>false</useAlternateLoadableFile> | |||
<parseOnProdLoad>false</parseOnProdLoad> | |||
<alternateLoadableFile></alternateLoadableFile> | |||
</loading> | |||
<subordinates> | |||
</subordinates> | |||
</compileType> | |||
<makeCustomizationType> | |||
<makeCustomizationPreStepEnabled>false</makeCustomizationPreStepEnabled> | |||
<makeCustomizationPreStep></makeCustomizationPreStep> | |||
<makeCustomizationPostStepEnabled>false</makeCustomizationPostStepEnabled> | |||
<makeCustomizationPostStep></makeCustomizationPostStep> | |||
<makeCustomizationPutChecksumInUserID>false</makeCustomizationPutChecksumInUserID> | |||
<makeCustomizationEnableLongLines>false</makeCustomizationEnableLongLines> | |||
<makeCustomizationNormalizeHexFile>false</makeCustomizationNormalizeHexFile> | |||
</makeCustomizationType> | |||
<HI-TECH-COMP> | |||
<property key="additional-warnings" value="true"/> | |||
<property key="asmlist" value="true"/> | |||
<property key="default-bitfield-type" value="true"/> | |||
<property key="default-char-type" value="true"/> | |||
<property key="define-macros" value=""/> | |||
<property key="disable-optimizations" value="false"/> | |||
<property key="extra-include-directories" value=""/> | |||
<property key="favor-optimization-for" value="-speed,+space"/> | |||
<property key="garbage-collect-data" value="true"/> | |||
<property key="garbage-collect-functions" value="true"/> | |||
<property key="identifier-length" value="255"/> | |||
<property key="local-generation" value="false"/> | |||
<property key="operation-mode" value="free"/> | |||
<property key="opt-xc8-compiler-strict_ansi" value="false"/> | |||
<property key="optimization-assembler" value="true"/> | |||
<property key="optimization-assembler-files" value="true"/> | |||
<property key="optimization-debug" value="false"/> | |||
<property key="optimization-invariant-enable" value="false"/> | |||
<property key="optimization-invariant-value" value="16"/> | |||
<property key="optimization-level" value="-O1"/> | |||
<property key="optimization-speed" value="false"/> | |||
<property key="optimization-stable-enable" value="false"/> | |||
<property key="pack-struct" value="true"/> | |||
<property key="preprocess-assembler" value="true"/> | |||
<property key="short-enums" value="true"/> | |||
<property key="undefine-macros" value=""/> | |||
<property key="use-cci" value="false"/> | |||
<property key="use-iar" value="false"/> | |||
<property key="verbose" value="false"/> | |||
<property key="warning-level" value="-3"/> | |||
<property key="what-to-do" value="ignore"/> | |||
</HI-TECH-COMP> | |||
<HI-TECH-LINK> | |||
<property key="additional-options-checksum" value=""/> | |||
<property key="additional-options-code-offset" value=""/> | |||
<property key="additional-options-command-line" value=""/> | |||
<property key="additional-options-errata" value=""/> | |||
<property key="additional-options-extend-address" value="false"/> | |||
<property key="additional-options-trace-type" value=""/> | |||
<property key="additional-options-use-response-files" value="false"/> | |||
<property key="backup-reset-condition-flags" value="false"/> | |||
<property key="calibrate-oscillator" value="false"/> | |||
<property key="calibrate-oscillator-value" value="0x3400"/> | |||
<property key="clear-bss" value="true"/> | |||
<property key="code-model-external" value="wordwrite"/> | |||
<property key="code-model-rom" value=""/> | |||
<property key="create-html-files" value="false"/> | |||
<property key="data-model-ram" value=""/> | |||
<property key="data-model-size-of-double" value="24"/> | |||
<property key="data-model-size-of-double-gcc" value="no-short-double"/> | |||
<property key="data-model-size-of-float" value="24"/> | |||
<property key="data-model-size-of-float-gcc" value="no-short-float"/> | |||
<property key="display-class-usage" value="false"/> | |||
<property key="display-hex-usage" value="false"/> | |||
<property key="display-overall-usage" value="true"/> | |||
<property key="display-psect-usage" value="false"/> | |||
<property key="extra-lib-directories" value=""/> | |||
<property key="fill-flash-options-addr" value=""/> | |||
<property key="fill-flash-options-const" value=""/> | |||
<property key="fill-flash-options-how" value="0"/> | |||
<property key="fill-flash-options-inc-const" value="1"/> | |||
<property key="fill-flash-options-increment" value=""/> | |||
<property key="fill-flash-options-seq" value=""/> | |||
<property key="fill-flash-options-what" value="0"/> | |||
<property key="format-hex-file-for-download" value="false"/> | |||
<property key="initialize-data" value="true"/> | |||
<property key="input-libraries" value="libm"/> | |||
<property key="keep-generated-startup.as" value="false"/> | |||
<property key="link-in-c-library" value="true"/> | |||
<property key="link-in-c-library-gcc" value=""/> | |||
<property key="link-in-peripheral-library" value="false"/> | |||
<property key="managed-stack" value="false"/> | |||
<property key="opt-xc8-linker-file" value="false"/> | |||
<property key="opt-xc8-linker-link_startup" value="false"/> | |||
<property key="opt-xc8-linker-serial" value=""/> | |||
<property key="program-the-device-with-default-config-words" value="true"/> | |||
<property key="remove-unused-sections" value="true"/> | |||
</HI-TECH-LINK> | |||
<XC8-CO> | |||
<property key="coverage-enable" value=""/> | |||
</XC8-CO> | |||
<XC8-config-global> | |||
<property key="advanced-elf" value="true"/> | |||
<property key="gcc-opt-driver-new" value="true"/> | |||
<property key="gcc-opt-std" value="-std=c99"/> | |||
<property key="gcc-output-file-format" value="dwarf-3"/> | |||
<property key="omit-pack-options" value="false"/> | |||
<property key="output-file-format" value="-mcof,+elf"/> | |||
<property key="stack-size-high" value="auto"/> | |||
<property key="stack-size-low" value="auto"/> | |||
<property key="stack-size-main" value="auto"/> | |||
<property key="stack-type" value="compiled"/> | |||
<property key="user-pack-device-support" value=""/> | |||
</XC8-config-global> | |||
</conf> | |||
</confs> | |||
</configurationDescriptor> |
@ -0,0 +1,25 @@ | |||
<?xml version="1.0" encoding="UTF-8"?> | |||
<configurationDescriptor version="65"> | |||
<projectmakefile>Makefile</projectmakefile> | |||
<defaultConf>0</defaultConf> | |||
<confs> | |||
<conf name="default" type="2"> | |||
<platformToolSN></platformToolSN> | |||
<languageToolchainDir>/opt/microchip/xc8/v2.10/bin</languageToolchainDir> | |||
<mdbdebugger version="1"> | |||
<placeholder1>place holder 1</placeholder1> | |||
<placeholder2>place holder 2</placeholder2> | |||
</mdbdebugger> | |||
<runprofile version="6"> | |||
<args></args> | |||
<rundir></rundir> | |||
<buildfirst>true</buildfirst> | |||
<console-type>0</console-type> | |||
<terminal-type>0</terminal-type> | |||
<remove-instrumentation>0</remove-instrumentation> | |||
<environment> | |||
</environment> | |||
</runprofile> | |||
</conf> | |||
</confs> | |||
</configurationDescriptor> |
@ -0,0 +1,9 @@ | |||
<?xml version="1.0" encoding="UTF-8"?> | |||
<project-private xmlns="http://www.netbeans.org/ns/project-private/1"> | |||
<editor-bookmarks xmlns="http://www.netbeans.org/ns/editor-bookmarks/2" lastBookmarkId="0"/> | |||
<open-files xmlns="http://www.netbeans.org/ns/projectui-open-files/2"> | |||
<group> | |||
<file>file:/home/dev/Desktop/code/electronics/attiny10_mplab_test/tests9_timer_6000hz.X/main.c</file> | |||
</group> | |||
</open-files> | |||
</project-private> |
@ -0,0 +1,37 @@ | |||
<?xml version="1.0" encoding="UTF-8"?> | |||
<project xmlns="http://www.netbeans.org/ns/project/1"> | |||
<type>com.microchip.mplab.nbide.embedded.makeproject</type> | |||
<configuration> | |||
<data xmlns="http://www.netbeans.org/ns/make-project/1"> | |||
<name>tests9_timer_6000hz</name> | |||
<name>tests8_timer_6000hz</name> | |||
<name>tests7_timer_6000hz</name> | |||
<name>tests6_timer_6000hz</name> | |||
<name>tests5_timer_6000hz</name> | |||
<name>tests4_timer_6000hz</name> | |||
<name>tests3</name> | |||
<name>tests2</name> | |||
<name>tests1</name> | |||
<name>test2</name> | |||
<name>test1</name> | |||
<creation-uuid>1f6b2f6c-8c6d-40dd-a737-d73d987b2bef</creation-uuid> | |||
<make-project-type>0</make-project-type> | |||
<c-extensions>c</c-extensions> | |||
<cpp-extensions/> | |||
<header-extensions/> | |||
<asminc-extensions/> | |||
<sourceEncoding>ISO-8859-1</sourceEncoding> | |||
<make-dep-projects/> | |||
<sourceRootList/> | |||
<confList> | |||
<confElem> | |||
<name>default</name> | |||
<type>2</type> | |||
</confElem> | |||
</confList> | |||
<formatting> | |||
<project-formatting-style>false</project-formatting-style> | |||
</formatting> | |||
</data> | |||
</configuration> | |||
</project> |